CA 1510 – measurement kit with climate logger
Starter kit with CA1510 climate logger, software, power adapter, cable and case.
- Measurement range CO2: 0...5000 ppm
- Measuring range temperature: -10...60 °C - ?
- Measurement range moisture: 5...95% RH
- Memory for 1 million measurements
5 990
In stock
In stock
CA 1510 - climate logger measurement set for air quality
Data logger that measures and logs three physical quantities, CO2 (carbon dioxide), temperature and relative humidity. The CA1510 then calculates the air quality based on either
CO2 level or a combination of the three quantities. According to the National Board of Health and Welfare, the Swedish National Board of Housing, Building and Planning, a carbon dioxide level of 1000 ppm is a guideline that should not be exceeded in premises with sedentary work. Outdoors, a typical level is around 400 ppm and indoors in well ventilated areas 600...800 ppm.
As the carbon dioxide meter is easy to use, it can be used both as a portable or fixed instrument mounted on a wall. The logging interval is selected between 15 s and 2 h and the 8 MB memory is sufficient for 1 million samples. With a 10-minute logging interval, the long battery life lasts up to 45 days of logging. It is also possible to lock the instrument during logging, in which case no measurement values are shown on the display.
With Bluetooth communication, either a PC or an Android device can be connected to configure, download measurement data and generate reports. The PC software is in Swedish.
The CA 1510 has a magnet on the back for easy and quick setup. A wall holder and bench support are also available as accessories.
ATTENTION! Buy this starter kit when you buy your first CA1510, to include the cable required for reading out the measurement data.
Included in the starter kit
- The CA 1510 data logger for CO2, temperature and humidity
- Software
- Batteries
- USB adapter
- USB cable
- AC adapter
- Bag
- Factory protocol
| Measuring principle CO2 | NDIR technology |
| Measuring range CO2 | 0...5000 ppm CO2 |
| Accuracy CO2 | ±50 ppm ± 3% of the measured value |
| Dissolving CO2 | 1 ppm |
| Response time CO2, 63% | < 200 sec |
| Measuring principle °C | CMOS |
| Measuring range °C | -10...+60 °C |
| Accuracy °C | ± 0.5 °C |
| Resolution °C | 0.1 °C |
| Measuring principle %RH | Capacitive sensor |
| Measuring range %RH | 5...95% RH |
| Accuracy %RH | ± 2% RH |
| Resolution %%RH | 0.1% RH |
| Battery life | for example 45 days at 10 minute measurement intervals |
| Log interval | freely adjustable from every 15 seconds to every two hours |
This software is intended for the CA1510 and L452 data loggers.
Download and installation:
1. If you have an earlier version of DataView installed on your computer, make sure to uninstall it. RESTART THE PC
2. The downloaded file is a .zip file. Unzip the downloaded file to a location on the computer that you will remember
3. If your instrument is connected to the PC, make sure to disconnect it from the PC
4. Go to the folder that has been created in step 3
5. Install DataView by "right-clicking" the Setup.exe file and selecting "Run as administrator"
6. Select "Swedish" as the language at the start of the installation
7. Follow the instructions…
W10/11 tip:
It may be necessary to perform the installation by right-clicking the start icon and selecting "Run as ADMIN".
At the end of the installation, you may need to click OK to a few prompts.
A black DOS window appears briefly while the drivers are installed.
A PC with W10 must be restarted before you can use the software.
Similar products
CA 1510 – climate logger for air quality
Indoor climate meters for assessing indoor air quality
- Measuring range 0...5000 ppm CO2
- Measuring range temperature -10...60 °C
- Measurement range moisture 5...95% RH
- Memory for 1 million readings
